Instant Quote

Just how do you feel about How to Install a Bathtub?

Mounting a bath tub isn't specifically rocket science, yet it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging job. If the old bathtub is readily accessible, the project can move quickly; if you have to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to leave the old tub and embeded in the brand-new one. See to it you have qualified yourself for the work and also fit trying it. As opposed to employing a specialist to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your bathroom if you have currently gotten a brand-new tub and do not require to alter the plan of your previous water system pipes.
Your tools and product list must make up the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Getting ready for the Setup

Firstly, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its last setting.

Removing Old Taps

If you need to change old faucets with new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome due to the limited accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub up until the level checks out degree.
To mount faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and examine all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub and also check the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bathtub should wait until the bathtub has actually been utilized a minimum of once as this will settle it right into its last placement.

Suitable New Taps

If the tails of the new faucets are plastic, then you will need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washing machines remain in area in between the tap as well as the sink. Secure the tap in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be attached to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

Tiling Around the Bath tub

In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, creating the water to pass through the wall in between the bathroom and the tiling, leading to issues with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealer can crack fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles making use of waterproof or waterproof sticky and also grout.

Bathtub Installation

How Important Is A Bathtub To Your Home?

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

Install Piping Before Tub

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

Position the Tub

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

Assemble Drain Connections

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

Place a Pipe For the Shower Head

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

Attaching Hot and Cold Water Lines

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

Install the Spout

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

Check For Leaks

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

estore the Bathroom Wall

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

As a devoted reader on How to Install a Bathtub Yourself, I thought sharing that article post was a good thing. Please take the opportunity to promote this blog if you enjoyed it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.

Recurring Service Plans